GEM Car Diagnostics and Programming Kit
For the T3 Controller
If you have the GE IC3645SR7A353T3 Controller
You can Now Program or Diagnose Failures Using GE Sentry Software.
These Controls are Generally Used in 2005 Models.
This Type of Controller Does Not Have the Communications Data Port
So a Special Programming Interface Cable is Necessary to Communicate.
Not sure which Controller you Have?
Click Here
Kit Includes everything you need:
Service CD Includes:
- GE Sentry Software 4.07
- GE Operating and Maintenance Manual for your T3 Traction Control
- 9 Page Detailed Hookup/Programming Instructions
- T3 Data Base File for Proper Function Definitions
- Special Programming Interface Cable
- 6 Foot Shielded DB9 Extension Cable
The GE Manual includes:
- Complete Theory Of Operation
- Elementary Wiring Diagrams
- 23 Pin Main Plug Function Listing
- Troubleshooting and Diagnostic Help
- Status (Fault) Code Explainations
- Complete Function Settings Guide
- Read, Print and Save Your original Settings
- Change and Download New Settings
- Access 16 Stored Fault Codes
What Others Have said:
Your kit worked perfectly. I changed #13 rolling radius in inches from 104 to 113.
My speed went from 32 mph to about 37 mph.
Thanks,
Pete
My computer has windows XP professional version 2002 service pack 3.
I used Belkin USB/Serial adapter: P73737/F5U409-CU.
I was happy with all your instructions.
The Auto Select port did not work. My son said the program was selecting a
modem that was using Comm 3 instead of the USB/Serial adapter plugged into Comm 5.
We manually selected Comm 5 and then the card downloaded perfectly.
I used Belkin USB/Serial adapter: P73737/F5U409-CU.
I was happy with all your instructions.
The Auto Select port did not work. My son said the program was selecting a
modem that was using Comm 3 instead of the USB/Serial adapter plugged into Comm 5.
We manually selected Comm 5 and then the card downloaded perfectly.
Thanks
Hey Bob I got my programmer today, I tried it and it works great.
I did just like the other guy and changed #13 to the same settings as he did and I get
20mph on the SPEEDO, so that is really 40mph since I have the 7.5HP motor and the 4 pole magnet
to fool the controller and I turned the regen off so it free wheels better and saves battery life, it works like a charm.
I have windows XP Home Edition and a BELKIN USB to SERIAL CONVERTER
Thanks,
Tony
Hey Bob I got my programmer today, I tried it and it works great.
I did just like the other guy and changed #13 to the same settings as he did and I get
20mph on the SPEEDO, so that is really 40mph since I have the 7.5HP motor and the 4 pole magnet
to fool the controller and I turned the regen off so it free wheels better and saves battery life, it works like a charm.
I have windows XP Home Edition and a BELKIN USB to SERIAL CONVERTER
Thanks,
Tony
The Interface cable connects to your Laptop or PC and to the 23 Pin Main Plug on your T3 Controller.
The Detailed Instructions take you step by step through the Software Setup.
DB9 Serial Port Computer Connector
PLEASE NOTE: This cable is a 9 Pin DB9 Serial Port Cable. Make sure your computer you plan to use has a True Serial Port.
The Serial Port on your computer will have 9 Male Pins, do not confuse this with the monitor connector.
I have used USB to Serial Converters, some work some don't, I have had good success with the
Sabrent Cable Make sure any you try has over 230kbps Data Transfer Rate.
We have been supplying Programming Kits for Electric Forklifts using GE Sentry Software since it was first a DOS program.
We are fully authorized by GE to distribute this software and it comes direct from GE.
See our other Kits here: Forklift Electronics Store
Purchase the Complete Kit Using PayPal's Secure Site
If You have the T4/T5 Series Control without a Data Port Plug, There is a Dedicated Kit For your Controller:
T4 Diagnostic and Programming Kit
If You have the T2 Series Control with a 12 Pin Data Port Plug, There is a Dedicated Kit For your Controller:
T2 Diagnostic and Programming Kit
If You have the T1 Series Control with an 8 Pin Data Port Plug, There is a Dedicated Kit For your Controller:
T1 Diagnostic and Programming Kit
If you have the 353E1 Controller Used on the Zenn Car
Zenn Car Diagnostic and Programming Kit
If you have the 262TB1 Controller Used on the Tomberlin NEV
Tomberlin EV Diagnostic and Programming Kit
PLEASE NOTE: Certain Parameters should not be changed from Factory Settings,
Forklift Electronics Is Not Responsible for any changes made to your existing settings.
Forklift Electronics
Home Index Page
2025