Tomberlin Diagnostics and Programming Kit
For the 262 or 403TB1 Controller
If you have the GE IC3645SH4V262 or 403TB1 Controller
You can Now Program or Diagnose Failures Using GE Sentry Software.
 262TB1 |
 403TB1 |
This Type of Controller Does Not Have the Communications Data Port
So a Special Programming Interface Cable is Necessary to Communicate.
Two Kits are Available ... Standard and Special
Click To Enlarge
Standard Kit Includes everything you need:
Service CD Includes:
- GE Sentry Software 4.07
- GE Operating and Maintenance Manual for your 262 Traction Control
- 10 Page Detailed Hookup/Programming Instructions
- 262TB1 Data Base File for Proper Function/Setting Definitions
- Special Programming Interface Cable
- 6 Foot Shielded DB9 Extension Cable
The GE Manual includes:
- Complete Theory Of Operation
- Elementary Wiring Diagrams
- 23 Pin Main Plug Function Listing
- Troubleshooting and Diagnostic Help
- Status (Fault) Code Explainations
- Complete Function Settings Guide
- Read, Print and Save Your original Settings
- Change and Download New Settings
- Access 16 Stored Fault Codes
NEW.......Special Data Port Kit
Some Tomberlin EVs come with a Data Port Pre-Installed
 |
 Click To Enlarge |
This Data Plug allows full Sentry Monitoring and Graphing Functions and Includes
Everything the Standard Kit Includes, except the Standard Cable is replaced with the Special Cable
Please email us to let us know if you have this Connector under the seat
What Others Have said:
I can't believe this, but this worked like a charm first time out. No problem at all.
Your directions were AMAZINGLY thorough! I upped the speed limit value and got my cart up to 30 mph first time out.
The max value was "255" so I just changed it to "255".
Thanks for all your help. You have been terrific.
I'm going to let everyone know about you and get some business thrown your way!!
Joel
Got it. Works perfectly.
tnx
Dave
this works with the E-4 403 controller also!
Read More About programming GEM Cars Here:
Programming the Cheap Way
The Standard Kit Includes an Interface cable that connects to your Laptop or PC and to the 23 Pin Main Plug on your 262 Controller.
The Detailed Instructions take you step by step through the Software Setup.
Click To Enlarge
DB9 Serial Port Computer Connector
Click to Enlarge
PLEASE NOTE: This cable is a 9 Pin DB9 Serial Port Cable. Make sure your computer you plan to use has a True Serial Port.
The Serial Port on your computer will have 9 Male Pins, do not confuse this with the monitor connector.
I have used USB to Serial Converters, some work some don't, I have had good success with the
Sabrent Cable Make sure any you try has over 230kbps Data Transfer Rate.
.
We have been supplying Programming Kits for Electric Forklifts using GE Sentry Software since it was first a DOS program.
We are fully authorized by GE to distribute this software and it comes direct from GE.
See our other Kits here: Forklift Electronics Store
Purchase the Complete Standard Kit Using PayPal's Secure Site
If You have the T4 Series Control without a Data Port Plug, There is a Dedicated Kit For your Controller:
T4 Diagnostic and Programming Kit
If You have the T3 Series Control without a Data Port Plug, There is a Dedicated Kit For your Controller:
T3 Diagnostic and Programming Kit
If You have the T2 Series Control with a 12 Pin Data Port Plug, There is a Dedicated Kit For your Controller:
T2 Diagnostic and Programming Kit
If You have the T1 Series Control with an 8 Pin Data Port Plug, There is a Dedicated Kit For your Controller:
T1 Diagnostic and Programming Kit
If you have the 353E1 Controller Used on the Zenn Car
Zenn Car Diagnostic and Programming Kit
PLEASE NOTE: Certain Parameters should not be changed from Factory Settings,
Forklift Electronics Is Not Responsible for any changes made to your existing settings.
Forklift Electronics
Home Index Page
2025